We start the build with the diodes. They are little components which only allow electricity to flow in one way, and they are required for the keyboard to properly tell key presses apart. Your kit will come with either through-hole or SMD diodes.
Which side? Each PCB has a bottom side and a top side. Look for the markings in hexagons on your board: you’ll see an arrow pointing toward the top on one side, and an arrow pointing toward the bottom on the other. Similarly, each kit has two PCBs: a left side and a right side, denoted by an L and an R within a hexagon on either side. These markings are used throughout the guide to help you find where to place the components.
Using Kailh Low Profile Choc Switches. Because of the lower profile of Choc switches, soldering the components to the bottom of the PCB is required. If you don't, there won't be enough room for the switch plate! When using choc switches and an aluminum plate it is important to make sure there aren't any metal parts sticking out. It should be as flush as possible. It is recommended to use SMD diodes.
Spares. You might have some spares left over after this step. That's expected: you'll be able to make some mistakes or lose a few without it being stressful ;)
Installing through-hole diodes
If you’re using SMD diodes, please skip to the next section on this page.
The diodes positions are usually all placed next to switches, all oriented the same way where possible. They’ll be marked with a D followed by a number, like D14.
Start by familiarizing yourself with their orientation. On through-hole diodes, there’ll be a black line which will need to match up with the square hole and the thick white line on the PCB.
Start by bending the diodes. You can use a special tool for it, called a lead bender, but you can also stack some layers of your case together and bend them using those. The distance between the legs of the diode should be around 6.5mm. It doesn’t have to get that precise: as long as the general shape is right, the legs will correct themselves a little when you push the diode through the holes on the PCB.
Diodes are directional. They only work in one direction, so pay attention while inserting the diodes into their positions.
Face the PCB with its bottom side toward you, and slide the diode legs through the holes.
You can bend the legs on the top side of the PCB so the diodes will stay in place while you install them. It is usually fastest to insert all diodes in place before soldering.
With all the diodes in place, look through all of them one more time to verify they are oriented correctly. If the line doesn’t match up with the square pad, take the diode out and place it back in correctly.
You can solder the diodes either from the top or bottom side. Soldering from the top (switch side, first image) is a little easier, while soldering from the bottom (diode side, second image) makes you able to snip the legs off a little bit flusher, which is only useful when using Choc low profile switches without hotswap sockets in combination with an acrylic plate. Whew!
After soldering the diodes, clip off the diode legs from the top side of the PCB. Hold the leg with one hand while you clip it with the other - you don't want a rogue leg flying into your eyes!
Encoders: Using a rotary encoder? You'll still need to install a diode in its location. Most rotary encoders also act as a button, which is the same as a switch - thus requiring a diode.
If you’re planning on socketing the microcontrollers, you might want to save the clipped off legs to use them as pins later.
Installing SMD diodes
If you just installed through-hole diodes, please continue to the next page.
The diodes positions are usually all placed next to switches, all oriented the same way where possible. They’ll be marked with a D followed by a number, like D14.
Start by familiarizing yourself with their orientation. On SMD diodes, there’ll be a gray or white line on the body of the diode which will need to match up with the square hole and the thick white line on the PCB.
Face the PCB with its bottom side toward you, and solder some tin on one of the two rectangular pads on the diode footprint. Leave the pads with holes alone - you won’t need them for SMD diodes.
Grab a diode using tweezers in one hand, and use your soldering iron with your other hand. Move the diode next to a pad you just soldered, and heat up the solder until it melts.
Then, move the diode in place, touching both the diode leg and the pad with your soldering iron until you notice a solder joint form — this usually only takes a second or two.
Remove the soldering iron, wait until the solder joint solidifies. Then release the tweezers, and repeat this process for all of the diodes.
Diodes are directional. They only work in one direction, so pay attention while soldering the diodes into their positions.
Solder the other joint. This one should go a lot easier as the first one is already holding the diode in place, so you don't need to use tweezers anymore.
Verify that you soldered all diodes in the correct orientation.
Encoders: Using a rotary encoder? You'll still need to install a diode in its location. Most rotary encoders also act as a button, which is the same as a switch - thus requiring a diode.